1. Cheng X, Yuan C, Blackburn S, et al. The study of the influence of binder systems in an Y2O3 -ZrO2, facecoat material on the investment casting slurries and shells properties[J]. Journal of the European Ceramic Society, 2014, 34(12):3061-3068. 2. Cheng X, Sun X D, Yuan C, et al. An investigation of a TiAlO based refractory slurry face coat system for the investment casting of Ti-Al alloys[J]. Intermetallics, 2012, 29(29):61-69. 3. Cheng X, Yuan C, Green N R, et al. Sintering mechanisms of Yttria with different additives[J]. Ceramics International, 2013, 39(5):4791-4799. 4. Cheng X, Yuan C, Green N R, et al. Enhanced sintering properties of yttria face coat by addition of B2O3, YF3, Al2O3 and ZrO2[J]. Materials Science & Technology, 2013, 29(3):351-356. 5. ChengX, Chen Y, Green N, et al. Evaluation of the inertness of investment casting molds using both sessile drop and centrifugal casting methods[J]. Metallurgical & Materials Transactions A, 2013, 44(2):888-898. 6. Cheng X, Yuan C, Blackburn S, et al. Influence of Al2O3 concentration in yttria based face coats for investment casting Ti-45Al-2Mn-2Nb-0.2TiB alloy[J]. Materials Science and Technology, 2014, 30(14): 1758-1764. 7. Cheng X, Yuan C, Green N R, et al. The Study of the oxidation of a Ti-45Al-2Nb-2Mn-0.2B alloy in the investment casting using an Yttria face coat mould[J]. Oxidation of Metals, 2014, 81(1-2):287-298. 8. Cheng X, Yuan C, Shevchenko D, et al. The influence of mould pre-heat temperature and casting size on the interaction between a Ti-46Al-8Nb-1B alloy and the mould comprising an Al2O3, face coat[J]. Materials Chemistry & Physics, 2014, 146(3):295-302. 9. Cheng X, Yuan C, Blackburn S, et al. A comparison of the chemical inertness of two Y2O3 -Al2O3-ZrO2 and Y2O3-Al2O3 face coat materials through sessile drop and investment casting methods[J]. Metallurgical & Materials Transactions A, 2014, 45(7):3116-3124. 10. Cheng X, Yuan C, Holt G, et al. Interactions between high Nb containing TiAl alloy and yttria facecoat during investment casting[J]. Cast Metals, 2015, 28(5):283-289. 11. Cheng X, Chai L, Wu G, et al. Evaluation of interfacial interactions between Ti-6Al-4V and mold use Ti-added backup coat in investment casting[J]. Metallurgical & Materials Transactions A, 2016, 47(5):1-6. 12. Chen X, Zhang J, Chen X, Cheng X*, et al. Electron beam welding of laser additive manufacturing Ti-6.5Al-3.5Mo-1.5Zr-0.3Si titanium alloy thic plate[J]. Vacuum, 2018, 151: 116-121. 13. Li J, Cheng X*, Liu D, et al. Phase evolution of a heat-treatable aluminum alloy during laser additive manufacturing[J]. Materials Letters, 2018, 214:56-59. 14. Li Y, Cheng X*, Liu D, et al. Influence of last stage heat treatment on microstructure and mechanical properties of laser additive manufactured AF1410 steel[J]. Materials Science & Engineering A, 2018, 713:75-80. 15. Shen, M Y, Tian X J, Liu D, Tang H B, Cheng X*, Microstructure and fracture behavior of TiC particles reinforced Inconel 625 composites prepared by laser additive manufacturing[J]. Journal of Alloys and Compounds, 2018,734: 188-195. 16. Yang C, Cheng X*, Tang H, et al. Influence of microstructures and wear behaviors of the microalloyed coatings on TC11 alloy surface using laser cladding technique[J]. Surface & Coatings Technology, 2017, 337: 97-103. 17. Li J, Cheng X*, Li Z, et al. Improving the mechanical properties of Al-5Si-1Cu-Mg aluminum alloy produced by laser additive manufacturing with post-process heat treatments[J]. Materials Science and Engineering: A, 2018, 735: 408-417. 18. Li G C, Cheng X*, Tian X J. Effects of annealing temperature and cooling rate on microstructures of a novel titanium alloy Ti-6Al-2V-1.5Mo-0.5Zr-0.3Si manufactured by laser additive manufacturing[J]. Journal of Iron and Steel Research International, 2018, 25(4): 442-452. 19. Jiao Z, Fu J, Li Z, Cheng X*, et al. The spatial distribution of α phase in laser melting deposition additive manufactured Ti-10V-2Fe-3Al alloy[J]. Materials & Design, 2018, 154:108-116. 20. Jiao Z, Ma C, Fu J, Cheng X*, et al. The effects of Zr contents on microstructure and properties of laser additive manufactured Ti-6.5Al-3.5Mo-0.3Si-xZr alloys[J]. Journal of Alloys & Compounds, 2018, 745. |
